JIS Marine Valves
Screw-Down Check Valves (SDNR) on Ships
A screw-down check valve stops reverse flow like a check valve and shuts tight like a globe valve: how it works, how it differs from other valves, and where SOLAS, the Load Line Convention and class rules call for one.

What is a screw-down check valve?
A screw-down check valve is a globe or angle valve whose disc is not fixed to the stem. With the stem screwed down it shuts the line like any stop valve; with the stem raised, the disc lifts only when the flow comes from the inlet side and drops back onto its seat when the flow reverses. It is a shut-off valve and a non-return valve in one body.
The same valve has several names: screw-down non-return valve (SDNR) in British and IMO usage, stop-check valve in American rules, and screw-down check valve in the JIS standards.
In the JIS system these valves are covered today by JIS F 7427 (bronze valves) and JIS F 7425 (cast iron valves); the legacy codes in brackets are still the usual way to order them (see JIS marine valve codes). The screw-down check valves in our catalogue:
- JIS F7427 (F7351) – bronze, globe pattern, 5K
- JIS F7427 (F7352) – bronze, angle pattern, 5K
- JIS F7427 (F7409) – bronze, globe pattern, 16K
- JIS F7427 (F7410) – bronze, angle pattern, 16K
- JIS F7425 (F7353) – cast iron, globe pattern, 5K
- JIS F7425 (F7354) – cast iron, angle pattern, 5K
- JIS F7425 (F7375) – cast iron, globe pattern, 10K
How does it work?
The flow enters under the disc. When the pressure on the inlet side is higher, it lifts the disc and the medium passes; when the flow stops or tries to run backwards, the disc drops onto the seat and closes the line by itself.
The stem works as an adjustable stop:
- raised, it lets the disc lift freely – the valve works as a non-return valve;
- partly lowered, it limits how far the disc can lift, and so the flow;
- screwed fully down, it presses the disc onto the seat – the valve is shut in both directions.
Opening the handwheel therefore never lets the flow run backwards. It only allows the disc to lift for flow in the forward direction.
How is it different from a globe valve or a check valve?
- Globe valve: the disc is fixed to the stem, so the valve opens and closes only with the handwheel and does not stop reverse flow.
- Check valve (lift or swing): it stops reverse flow by itself but cannot be shut by hand. A metal-seated check valve may let a little through in reverse, so a check valve is never used to isolate a line.
- Screw-down check valve: both functions in one body. To isolate a line for work, close it with the handwheel – do not rely on the non-return function alone.
Where do ship rules require it?
The international rules describe the function – water must not pass the wrong way – and the classification societies turn it into valve types:
- SOLAS Chapter II-1, Regulation 35-1 (bilge pumping): the bilge system must prevent water passing from the sea or from water ballast spaces into cargo and machinery spaces, or from one compartment to another. SOLAS asks for non-return valves at certain points, for example on the direct bilge suction from the main circulating pump of passenger ships and on bilge pipes that run close to the ship’s side.
- Class rules: DNV, for example, requires the valves of bilge distribution chests and of direct or branch bilge suctions to be screw-down non-return valves, and accepts a non-return valve and a shut-off valve in series as an equivalent. Other classification societies have similar rules.
- Load Line Convention, Regulation 22: a discharge from a space below the freeboard deck normally needs an automatic non-return valve with a positive means of closing from above the freeboard deck; other arrangements depend on the height of the inboard end above the summer load line. Regulation 22-1 asks for a screw-down non-return valve on garbage chutes.
- US rules (46 CFR 56.50-50): every bilge manifold valve that controls a compartment suction must be of the stop-check type.
For valves on the ship’s side, SOLAS and the Load Line Convention accept steel, bronze or other ductile material, not ordinary cast iron – check the body material against the valve’s position in the ship. Which rules apply to a ship depends on its flag and its classification society: please name both in your enquiry.
Where is it used on board?
- bilge distribution chests and direct bilge suctions;
- the emergency bilge suction from the sea-water cooling or circulating pump;
- between the ballast or sea side and the bilge suctions;
- overboard discharges that need a positive means of closing;
- garbage chutes.
Installation and maintenance
- Fit the valve with the flow in the direction of the arrow on the body – the flow enters under the disc.
- Globe-pattern valves go in horizontal lines, or in vertical lines with upward flow; the angle pattern turns the flow through 90°.
- Rust, rags or cargo residue can hold the disc open. Check regularly that the bilge lines pump one way only, and inspect disc and seat at the intervals of the ship’s maintenance plan.
- An overhaul usually means cleaning and lapping disc and seat and renewing the gland packing.
The test pressures of each valve are on its product page; how the pressure class decides them is explained in JIS 5K, 10K and 16K pressure classes.
Questions buyers ask
- Is a screw-down check valve the same as a stop-check valve?
- Yes. It is the same function under British/IMO and American names; the JIS standards call it a screw-down check valve.
- Does opening the handwheel let water flow back?
- No. The handwheel only sets how far the disc can lift for forward flow; reverse flow presses the disc onto its seat.
- Can a check valve and a gate valve replace it?
- Some class rules accept a non-return valve and a shut-off valve in series as an equivalent – DNV does. Ask the ship’s classification society before changing an arrangement.
- Globe or angle pattern?
- The globe pattern is for straight lines; the angle pattern is used where the line turns through 90°, so it saves an elbow.
- Which JIS codes are screw-down check valves?
- Bronze: JIS F7427 (legacy F7351, F7352, F7409, F7410). Cast iron: JIS F7425 (legacy F7353, F7354, F7375). See JIS marine valve codes.
Request a quote
Tell us the sizes and quantities you need — we reply with a quote.
Screw-Down Check Valves (SDNR) on Ships















