JIS Marine Valves
How to Order JIS Marine Valves: A Buyer’s Checklist
What an enquiry for JIS marine valves should say so that the right valve arrives: code and type, material, pressure class, size in A or B, end connection, certificates (EN 10204 and class) and IMPA codes – with an example list.

The short answer
A few details name a JIS marine valve beyond doubt: the code or standard and the type (for example F7301, a bronze globe valve), the body material, the pressure class (5K, 10K or 16K), the nominal size, the end connection and – for cast iron valves – the trim series. Add the quantity and the certificate your ship or its classification society needs, and an enquiry can be answered line by line without questions back. The JIS valve standards designate a valve in much the same order: standard, nominal pressure, nominal size and type – for example “marine bronze 5K-15 globe valve”.
The checklist, point by point
- Code, or standard and type. Buyers, ship drawings and the IMPA guide still use the old codes (F7301, F7409 …); the current standards are JIS F 7427 for bronze, JIS F 7425 for cast iron and JIS F 7426 for cast steel valves. Our pages give both, for example JIS F7427 (F7301). Some codes cover more than one class – the F7334 hose valves come in 5K and 10K – so add the class. More in JIS marine valve numbers explained.
- Type. Globe, angle, screw-down check (globe or angle pattern), gate, hose or storm valve. A globe valve and a screw-down check valve look alike from outside – see screw-down check valves and globe, angle or gate valve.
- Body material and position on board. Bronze, cast iron or cast steel. Say where the valve goes: ordinary cast iron is not accepted at the ship’s side or on the collision bulkhead – see marine valve materials for sea water.
- Trim series (cast iron valves). JIS F 7425 knows two: the B series with disc, seat and stem of copper alloy, and the S series with stainless steel ones. The materials of each of our valves are listed on its product page.
- Pressure class. 5K, 10K or 16K – the class of the pipe flanges the valve is bolted to. See JIS 5K, 10K and 16K pressure classes.
- Nominal size, with its letter. JIS writes sizes in millimetres with an A (15A, 50A) or in inches with a B (1/2B, 2B); 50A and 2B are the same size. A bare figure on an old list – “2” or “2 1/2” – is easily misread, so write 50A or DN 50.
- End connection. Flanged, in the valve’s own class; for hose valves also the coupling – our hose valves have the Nakajima coupling.
- Quantity – one line for each type, class and size.
- Certificate and tests. The EN 10204 document type (2.2, 3.1 or 3.2) and, where the class rules ask for it, the classification society’s certificate – see the next section. JIS valves are pressure-tested with water to JIS F 7400, body and seat; if a surveyor or your own inspector must witness the test, say so in the enquiry.
- IMPA code, if you order from an IMPA list or through a ship chandler – the code already stands for one item and size.
- Extras: spare gland packing and gaskets, tags with your tag numbers, packing, the delivery date and place.
Which certificate?
EN 10204 (2004 edition, still current) defines four inspection documents:
- 2.1 – declaration of compliance with the order: the manufacturer states that the products meet the order; no test results.
- 2.2 – test report: the same statement with results of routine tests on products of the same kind – not necessarily the ones delivered.
- 3.1 – inspection certificate: results of tests on the delivered products themselves, validated by the manufacturer’s authorised inspection representative, who is independent of manufacturing.
- 3.2 – inspection certificate: as 3.1, but validated also by the purchaser’s representative or by the inspector named in the official regulations – on ships, for example, a classification society’s surveyor.
Class rules come on top. Under IACS UR P2 (Türk Loydu publishes it as TL-R P2), the materials of valves in pipe classes I and II and of valves on the ship’s side and the collision bulkhead are tested to the class rules; for class III the society may accept works certificates. Valves for classes I and II are pressure-tested at 1.5 times the design pressure, ship-side valves at no less than 5 bar. A type approval confirms that a design meets the class rules; it does not replace the tests and the product certificate the rules ask for each delivered valve. Which of them a valve needs depends on the society, the system and the position – name the society and the pipe class in your enquiry.
Ask in time: a 3.2 certificate and a class product certificate both need the inspector at the tests, before delivery. They cannot be issued afterwards.
Replacing an old valve: what the body tells you
When a list only says “same as old”, start with the old valve. Under the JIS valve standards the body of a globe, angle or screw-down check valve is marked with:
- the nominal pressure and the nominal size – for example 5K and 50;
- an arrow for the flow direction (gate valves have none – they work both ways);
- the manufacturer’s name or mark and the year and month of manufacture.
A screw-down check valve also has a cross-shaped groove on the head of its stem – the quickest way to tell it from a plain globe valve, which looks the same from outside. What the body does not show is the standard number, the old code and the material: those come from the ship’s drawings and spare-part lists, earlier orders or the IMPA code. If none is left, send a photo of the valve and its marking with the main dimensions – the flange outside diameter, the number of bolt holes and the face-to-face length – so that they can be matched with the dimension tables of our product pages.
Five mistakes that delay an order
- An old code without the class – F7334, for example, exists in 5K and 10K.
- A size without its letter – is “2” two inches (2B = 50A) or size 20? Write 50A or 2B.
- A valve class that differs from the pipe flanges – a 5K valve does not bolt to a 10K flange.
- Cast iron at the ship’s side – the rules exclude ordinary cast iron there; choose bronze or cast steel.
- A certificate asked for after the order – 3.2 and class certificates must be planned before the tests.
An example enquiry
A list in this form can be answered at once:
- JIS F7427 (F7301) bronze globe valve, 5K, 50A, flanged – 6 pcs (IMPA 750126)
- JIS F7425 (F7354) cast iron screw-down check angle valve, 5K, 100A, flanged – 2 pcs
- JIS F7425 (F7363) cast iron gate valve, 5K, 200A, flanged – 1 pc
- Certificate: EN 10204 3.1 · Classification society: (name) · Delivery: (port, date)
JIS valves in our catalogue
Our range includes JIS bronze valves (5K, 10K and 16K, DN 15–65) and JIS cast iron and cast steel valves (5K and 10K, DN 50–500). Every product page shows the sizes, materials, test pressures, drawing and dimension table with the IMPA code of each size, and offers a datasheet (PDF). Send your list – with the points above, or simply the old codes, classes and sizes – through “Request a quote” on any product page.
Questions buyers ask
- Can I order by IMPA code alone?
- Yes. An IMPA code stands for one item description, size included; add the quantity and the certificate you need. The code describes the item, not a brand.
- What are IMPA codes?
- The six-digit codes of the IMPA Marine Stores Guide, from which ship chandlers and ship managers order; its current, eighth edition lists more than 50,000 items. Valves and cocks are in section 75 – for example 750121, a 5K bronze globe valve (F7301) in size 15.
- What does 50A mean?
- Nominal size 50 in the millimetre series of JIS. The same size in the inch series is 2B; likewise 15A = 1/2B, 65A = 2 1/2B and 80A = 3B.
- What is the difference between EN 10204 3.1 and 3.2?
- Both give test results of the delivered products. A 3.1 is validated by an authorised inspection representative who is independent of manufacturing; a 3.2 also by the purchaser’s inspector or one named by the regulations, such as a classification society’s surveyor.
- Does the valve body show the JIS number?
- No. The JIS valve standards ask for the class, the size, the flow arrow, the manufacturer’s mark and the date – not the standard number or the material.
- Is there a datasheet for each valve?
- Yes – a PDF datasheet on every product page.
Request a quote
Tell us the sizes and quantities you need — we reply with a quote.
How to Order JIS Marine Valves: A Buyer’s Checklist















